- Cost of stripper (10,000 sq ft / 1,000 sq ft per gallon = 10 gallons x $15 = ($150) = 1.5 cents per square foot.
- Cost of finish (5 coats x 10,000 sq ft / 2000 sq ft per gallon = 25 gallons x $14ea = $350) = $.035 cents per square foot ($350)
- Cost of pads, mops, etc. (
Just so, how much do you charge for stripping and waxing floors?
A lot of customers and service providers ask, “What are the average prices for floor stripping and waxing services?” Nationally prices average between 30 to 60 cents per sq. ft.
Subsequently, question is, when you strip a floor what is the minimum coats of wax you apply? Since wax is expensive and cannot be poured back into the bucket, don't pour more wax than you need. To get the appearance you want on a newly stripped floor normally required three coats, allowing adequate time between coats (approximately a half hour to forty-five minutes if the humidity is high).
Correspondingly, how long does it take to strip and wax floors?
After the floor dries, apply a thin coat of wax with a clean mop, then let it dry completely for 10-30 minutes. Finally, reapply the wax according to the package instructions. For more tips, like how to strip hard-to-reach floor areas, read on!
How often do you strip and wax floors?
A strip and wax is recommended at least once a year on low to medium traffic floors, and every 4-6 months on high traffic floors.
What color pad is used for stripping?
Black Pads - Most Aggressive Heavy-duty scrubbing and stripping pad. Used for stripping floors or heavy duty scrubbing on very dirty floors.How many coats of wax should you put on a floor?
Applying 1st Coat of Wax - You do not want to run out of wax before the job is finished. Most wax finishes, like our Optimal Wet Look Floor Finish will cover approximately 2,000 square feet per gallon. Each finish is different, but most recommend 4 to 5 coats.How much should I charge for waxing?
The Costs. At Home: Do it yourself waxing kits cost between $25-$100. Salon or Spa: Expect to pay $30-$55 for a half leg (ankle to knee or knee to thighs, not including bikini zone — both legs) or $45-$100 for a full leg (ankle to thighs, not including bikini zone — both legs).How much does it cost to get your floor waxed?
Strip & Wax Floor Prices HomeWyse states that average cost to strip and wax a floor is about $174. The lowest cost you could expect to pay is about $148 while the highest cost is about $200. This cost estimate is based on a 314 sq ft room. This makes the average cost of stripping and waxing a floor at $1.80 per sq ft.How do you strip a floor without a machine?
Stripping Floor without Machinery- Sweep and dust mop floor.
- Using a putty knife or chewing gum removing solution, remove gum and sticky substances from floor.
- Prepare stripper solution per label directions in mop wringer/bucket set.
- Prepare a neutralizing solution in a second mop wringer and bucket set.
How do you charge for buffing floors?
The larger the floor area to be cleaned, the lower the cost per square foot.Size
- Over 10,000 square feet: 25 cents per square foot.
- 5,000-10,000 square feet: 39 cents per square foot.
- Up to 5,000 square feet: 50 cents per square foot.
How many square feet can one person clean per hour?
A facility of that size with full scope of cleaning can be cleaned around 3,300 square feet per hour.How do you get old wax off the floor?
Mix 1 gallon of warm water, 1 cup of white vinegar and 1 cup of cream of tartar in a bucket. Dip a mop into the solution and apply it to the floor. Allow it to sit for a few minutes until the wax softens. Scrub the floor in a circular motion, using a scrub brush.How do you strip wax off a wood floor?
Removing old wax from wood floors is time-consuming, but it is not an impossible task.- Sweep away loose dirt, dust and other debris, and mop the floor with warm water to remove any grime or residues from the wood's surface.
- Pour a small amount of mineral spirits directly onto a 2-square foot section of floor.
How long before you can walk on a waxed floor?
How long before I can walk on the floor? After we apply wax, you should not walk on the floor or allow pets on the floor for at least one hour. For polyurethane coating, we recommend at least 3 hours before walking on the floor.How long should floor wax dry before buffing?
Place a small amount of wax on the floor then buff evenly (A golf ball sized dollop will cover about a square yard). Allow about 30 minutes to dry then buff until a lustrous shine is apparent (It's not complicated!).How do you remove wax coating from porcelain tiles?
Porcelain tiles may have a wax coating applied at the factory.- Pour a small amount of wax stripper on the tile after installation for easiest wax removal.
- Scrub the tile with a poultice or nylon emulsifying pad.
- Rinse with water and a clean cloth.
- Repeat the process if necessary to remove all signs of the wax coating.
